You may also leave the gas there if you have new gas — in which case, you should just clamp the fuel line. Regardless of the method that you are going for, you should place a towel or a bowl at the bottom so that you may catch any stray drips. This is where the cleaning part actually starts. Check the carburetor for any residual fuel and drop it in a towel or in a container depending on how much fuel there is.
Once you have done that, you need to check whether the carburetor is corroded or dirty. Obviously, if the carburetor is corroded, then you have to buy a new one. However, if everything seems just fine, then you can go forward with the cleaning process. Here is where you should take one more picture of how the carburetor is connected. To do that, you may start by unscrewing the bottom of the unit in order to remove the carburetor bowl. This action will expose the float of your pressure washer, no matter if you are using a residential or one of the best professional pressure washers.
Take the other pieces apart in order. Bear in mind that if the parts are made of rubber, you should not use carburetor cleaner as it can be too harsh.
Regular soap and water should work just fine in this case. Rinse every piece properly and let them dry. With everything nice and clean now, all you have to do is put the carburetor back together in the order that you took it apart. Use the pictures that you took beforehand as a reference. Cleaning a pressure washer is not that big of a deal, and it is certainly something you can do without taking the unit into the repair shop. However, you have to be careful that you put back the pieces in the same order that you took them out.
Reference to your pictures to be safe. This is a cheaper alternative over taking it to a shop and can be a timesaver, as this can be done in less time than it takes to make the trips to the shop. Your carburetor is a device that ensures that your pressure washers engine has the right air to fuel mix. This ensures that the engine runs properly. The air to fuel ratio for pressure washer engines tends to sit somewhere between and , if you want your pressure washer to run its best, you need to maintain the air-fuel ratio within that sweet spot.
It may not burn the fuel as its meant to such as if a fuel valve is stuck, which can result in you consuming more fuel than necessary. Your carburetor is the heart of your power washer. This is because the air and fuel are unable to properly pass through the carburetor, so the motor is starved of what it needs, preventing it from starting.
While this can be because of a few different components, the first you should investigate is your carburetor. In the majority of cases, this is a sign that there is an imbalance in the air and fuel mix.
It may mean then you have to much fuel and not enough air going into the combustion chamber, and one of the problems that this can lead to is the formation of black smoke. The biggest tip I can give you and I use this tip for all sorts of DIY tasks is to take pictures of the entire assembly before you remove anything.
When you put the pressure washer back together, you should do so in the exact order you took it apart. I suggest laying a towel on a flat surface and laying each component out in the order in which you took it off, this makes it easier to work out when goes on next. This will make sure that no fuel will pass through the fuel line into your carburetor. Before you clean the carburetor, you should find the gas line that connects the carburetor and the fuel tank.
If your fuel tank is full of new fresh fuel, then you can clamp the fuel line. The carburetor performs the balancing between the air and the gas and make sure the ratio is right. In case the carburetor gets clogged up it cannot put the right mix of the air and gas, this results in a malfunctioned pressure washer.
As we mentioned earlier, your pressure washer can stop working due to many reasons. In case the problem is due to a clogged up carburetor, you will experience the following changes in your pressure washer.
Above were some of the symptoms of a clogged up carburetor. If your pressure washer is not working due to a clogged up carburetor, you will most likely see these symptoms. If you have experienced the mentioned changes in your pressure washer, it is confirmed that the carburetor is clogged up. Now you might be wondering, how it got dirty in the first place and what measures can you take in future to avoid this problem from happening again. Answer to your question is that your pressure washer gets clogged up because it has fuel sitting in it for a long period of time.
So to avoid this problem from happening again you need to either drain the fuel from your pressure washer or run your pressure washer for minutes every once in a while.
0コメント